Part A
ADE-1L+
ミニサーキット
- Lifecycle
- Active
- Stock
- 6401 個数
- Package
- SMD-6
- Series
- RFミキサー
Replacement verdict
Compatible functional replacement candidate
The ADE-1L+ is a viable functional replacement candidate for the ADE-12+ in many RF and microwave signal-chain applications, as both are surface-mount double-balanced mixers sharing a comparable frequency range and package family. However, the ADE-1L+ offers a lower LO drive level and slightly different conversion loss and isolation performance, so the designer must validate LO power budget, port-to-port isolation, and impedance matching against the specific system requirements before committing to a drop-in substitution.
Frequency Range
High match
LO Drive Level
Validation required
Conversion Loss
Validation required
Package Type
High match
Key differences
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADE-12+ | ADE-1L+ | Why it matters |
|---|---|---|---|
| Frequency Range | 10 MHz to 1200 MHz | 0.5 MHz to 500 MHz | Defines the band over which the mixer performs within spec; the two parts cover different portions of the spectrum, so substitutability depends on the operating frequency. |
| Conversion Loss (typ.) | 6.5 dB | 6.0 dB | Lower conversion loss improves receiver sensitivity and reduces the need for additional gain stages after the mixer. |
| LO Power Level | +7 dBm | +7 dBm | The required local oscillator drive level must match the system's LO source; both parts use the same nominal drive, easing LO design reuse. |
| Isolation (LO-RF, typ.) | 35 dB | 30 dB | Higher isolation reduces LO leakage to the RF port, which affects spurious performance and receiver dynamic range. |
| Input IP3 (typ.) | +14 dBm | +10 dBm | Third-order intercept indicates linearity and resistance to intermodulation; higher IIP3 supports stronger-signal environments. |
| Maximum RF Input Power | +17 dBm | +13 dBm | Sets the safe input power limit before damage or compression; the higher-rated part tolerates larger signals. |
| Package / Mounting | Surface mount, 6-lead | Surface mount, 6-lead | Footprint and assembly compatibility determine whether a part can be dropped into an existing board layout. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Confirms both parts meet the same environmental envelope for industrial and commercial applications. |
Need help validating a replacement?
Send your BOM and application constraints for technical and sourcing review.
Full specification comparison
Use manufacturer datasheets as the final authority.
| Specification | ADE-1L+ | ADE-12+ |
|---|---|---|
| Part Status | Active | Active |
| RF Type | Cellular | Cellular, UHF, VHF |
| Frequency | 2MHz ~ 500MHz | 50MHz ~ 1GHz |
| Mounting Type | Surface Mount | Surface Mount |
Frequently asked questions
What are the ADE-12+ and ADE-1L+ components?
The ADE-12+ and ADE-1L+ are frequency mixer components from Mini-Circuits. Both are double-balanced mixers used for frequency conversion in RF and microwave signal chains, but they differ in their specified operating frequency ranges and performance characteristics.
What is the operating frequency range of the ADE-12+ compared to the ADE-1L+?
The ADE-12+ is specified for an RF/LO frequency range of 10 to 1200 MHz and an IF range of DC to 800 MHz. The ADE-1L+ is specified for an RF/LO frequency range of 0.5 to 500 MHz and an IF range of DC to 500 MHz. The ADE-12+ therefore covers a wider and higher frequency range.
How do the conversion loss specifications compare between the ADE-12+ and ADE-1L+?
The ADE-12+ specifies a typical conversion loss of approximately 6.5 dB across its band. The ADE-1L+ specifies a typical conversion loss of approximately 6.0 dB. Both values are typical and should be verified against the latest Mini-Circuits datasheet for the specific operating conditions.
What are the LO power requirements for the ADE-12+ and ADE-1L+?
Both the ADE-12+ and ADE-1L+ are specified for a nominal LO drive level of +7 dBm. Designs should confirm the acceptable LO drive range from the manufacturer datasheet, as performance parameters such as conversion loss and isolation are defined at the nominal drive level.
Do the ADE-12+ and ADE-1L+ share the same package and pin configuration?
Both the ADE-12+ and ADE-1L+ are offered in Mini-Circuits' surface-mount package with the same pinout and footprint. This means PCB land patterns are compatible, but electrical differences in frequency range and performance must still be validated before substituting one for the other.
Can the ADE-1L+ be used as a direct replacement for the ADE-12+?
Not universally. The ADE-1L+ has a lower maximum RF/LO frequency (500 MHz versus 1200 MHz for the ADE-12+), so it cannot cover the full operating range of the ADE-12+. A substitution is only appropriate when the application's frequencies and performance requirements fall within the ADE-1L+ specifications and are verified against the manufacturer datasheet.
What isolation performance do the ADE-12+ and ADE-1L+ provide?
Both mixers specify typical LO-to-RF, LO-to-IF, and RF-to-IF isolation values in their respective datasheets. Isolation is frequency-dependent, so the applicable value must be read at the intended operating frequency. Designers should consult the current Mini-Circuits datasheet for each part rather than assuming identical isolation performance.
Which applications are better suited to the ADE-12+ versus the ADE-1L+?
The ADE-12+ is suited to applications requiring frequency conversion up to 1200 MHz, such as VHF/UHF receivers and transmitters. The ADE-1L+ is suited to lower-frequency applications up to 500 MHz, such as HF/VHF systems where its slightly lower typical conversion loss is advantageous. Selection should be based on the application's frequency plan and verified datasheet parameters.