ADM4852ARZ
テキサス・インスツルメンツ
- Lifecycle
- Active
- Stock
- 4726 個数
- Package
- SOIC-8
- Series
- インターフェース - ドライバ、レシーバ、トランシーバ
ADM4852ARZとADM4857ARの詳細な比較では、それぞれの仕様と主要機能に関する貴重な洞察を提供します。RoHS指令への準拠、REACH規則、シリーズ、実装スタイル、パッケージタイプ、その他の関連特性など、重要な要素を詳細に網羅しています。違いを並べて表示することで、部品選定が容易になり、特定のアプリケーションに最適なオプションを選択しやすくなります。
Replacement verdict
The ADM4852ARZ and ADM4857AR are both half-duplex RS-485/RS-422 transceivers in an 8-lead SOIC package with a 5 V supply and a 1/8 unit load, making them functionally interchangeable for most bus-node applications. The ADM4857AR offers a higher maximum data rate and a wider operating temperature range, so the ADM4852ARZ can serve as a lower-speed substitute where the extended temperature range is not required, while the ADM4857AR can replace the ADM4852ARZ in higher-speed designs. Verify the data rate and temperature requirements of the target application before substitution.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM4852ARZ | ADM4857AR | Why it matters |
|---|---|---|---|
| Data Rate | 2.5 Mbps | 10 Mbps | Determines the maximum communication speed the transceiver can support; a higher data rate allows faster bus throughput. |
| Duplex Mode | Half-duplex | Full-duplex | Half-duplex shares one pair for transmit/receive, while full-duplex uses separate pairs for simultaneous bidirectional communication. |
| Number of Drivers/Receivers | 1/1 | 1/1 | Indicates the transceiver channel count; both provide one driver and one receiver per package. |
| Operating Supply Voltage | 5 V | 5 V | The nominal supply voltage must match the system rail for proper logic-level compatibility and bus signaling. |
| Mounting Type / Package | Surface Mount, 8-SOIC | Surface Mount, 8-SOIC | Package and mounting style affect PCB footprint and assembly compatibility for drop-in substitution. |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | Defines the environmental range over which the device is guaranteed to operate reliably. |
| Receiver Input Impedance | 1/8 unit load (up to 256 nodes) | 1/8 unit load (up to 256 nodes) | Lower unit load allows more transceivers on the same bus without exceeding the standard's load limit. |
| Fail-Safe Receiver | Yes (open-circuit fail-safe) | Yes (open-circuit fail-safe) | Fail-safe receivers ensure a defined logic output when the bus is idle, open, or unterminated, preventing spurious data. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM4852ARZ | ADM4857AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.75V ~ 5.25V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Half | - |
| Receiver Hysteresis | 20 mV | - |
| Data Rate | 2.5Mbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM4852ARZ is a half-duplex RS-485/RS-422 transceiver specified for data rates up to 2.5 Mbps, while the ADM4857AR is a full-duplex RS-485/RS-422 transceiver specified for data rates up to 10 Mbps. The ADM4852ARZ is supplied in an 8-lead SOIC package, whereas the ADM4857AR is supplied in a 14-lead SOIC package, reflecting the additional driver/receiver pins required for full-duplex operation.
No. The ADM4852ARZ uses an 8-lead SOIC package with half-duplex pinout (single differential pair shared between driver and receiver), while the ADM4857AR uses a 14-lead SOIC package with separate driver and receiver differential pairs for full-duplex operation. The package body widths and pin counts differ, so they cannot be interchanged on the same PCB land pattern.
No. Beyond the package and pinout differences, the ADM4852ARZ is a half-duplex device and the ADM4857AR is a full-duplex device. A half-duplex transceiver cannot directly replace a full-duplex transceiver in a four-wire RS-485 system without redesigning the bus topology and control logic. The maximum data rate also differs (2.5 Mbps versus 10 Mbps), so timing margins must be revalidated.
The ADM4852ARZ is specified for data rates up to 2.5 Mbps. The ADM4857AR is specified for data rates up to 10 Mbps. These figures are taken from the respective Analog Devices datasheets and apply over the specified operating conditions.
Yes. Both the ADM4852ARZ and the ADM4857AR are specified for operation from a single 5 V ±5% supply, consistent with the Analog Devices ADM485x family datasheets. Designers should confirm the exact supply tolerance and current consumption from the respective datasheet for their operating conditions.
The ADM4852ARZ is half-duplex: the driver and receiver share one differential pair (A/B), requiring direction control (DE/RE) to switch between transmit and receive. The ADM4857AR is full-duplex: it provides separate driver outputs (Y/Z) and receiver inputs (A/B), allowing simultaneous transmit and receive over a four-wire bus. The bus wiring and protocol timing must be designed accordingly.
Both the ADM4852ARZ and ADM4857AR are offered in industrial temperature grade versions specified for −40°C to +85°C operation, per the Analog Devices datasheets. The "ARZ" and "AR" suffixes denote the SOIC package and industrial temperature range; designers should verify the exact ordering code and temperature grade against the manufacturer's ordering guide.
The ADM4857AR should be selected for a four-wire full-duplex RS-485 network because it provides independent driver and receiver differential pairs, enabling simultaneous transmission and reception. The ADM4852ARZ, being half-duplex, is suited to two-wire buses where transmit and receive are time-multiplexed.