ADM3076EARZ vs ADM3072EARZ

ADM3076EARZとADM3072EARZの詳細な比較では、それぞれの仕様と主要機能に関する貴重な洞察を提供します。RoHS指令への準拠、REACH規則、シリーズ、実装スタイル、パッケージタイプ、その他の関連特性など、重要な要素を詳細に網羅しています。違いを並べて表示することで、部品選定が容易になり、特定のアプリケーションに最適なオプションを選択しやすくなります。

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM3072EARZ and ADM3076EARZ are both 3.3 V RS-485/RS-422 transceivers from the same ADM307xE family in an identical 8-lead SOIC package, sharing the same supply voltage, pinout, and industrial temperature range. The primary distinction is the duplex configuration: the ADM3072EARZ is a half-duplex device, while the ADM3076EARZ is a full-duplex device. This makes them functionally interchangeable only where the bus topology and driver/receiver enable scheme permit, so the duplex requirement must be confirmed against the target design before substitution.

Duplex Configuration Validation required
Supply Voltage High match
Package Type High match
Operating Temperature High match

Parts at a glance

Part A

ADM3076EARZ

テキサス・インスツルメンツ

Lifecycle
Active
Stock
5876 個数
Package
SOIC-14
Series
インターフェース - ドライバ、レシーバ、トランシーバ
Part B

ADM3072EARZ

テキサス・インスツルメンツ

Lifecycle
Active
Stock
1320 個数
Package
SOIC-8
Series
インターフェース - ドライバ、レシーバ、トランシーバ

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM3072EARZ ADM3076EARZ Why it matters
Data Rate 250 kbps 16 Mbps Maximum signaling speed; determines whether the part can support the required bus bandwidth for the application.
Duplex Mode Half duplex Full duplex Half duplex shares one pair for transmit/receive, while full duplex uses separate pairs for simultaneous bidirectional communication.
Number of Drivers/Receivers 1/1 1/1 Indicates the transceiver channel count; both provide a single differential driver and receiver per package.
Receiver Input Impedance 1/8 unit load (96 kΩ) 1/8 unit load (96 kΩ) Determines how many nodes can share the bus; 1/8 unit load allows up to 256 nodes on a single RS-485 bus.
Fail-Safe Receiver Yes (open/short circuit) Yes (open/short circuit) Guarantees a defined logic output when the bus is idle, open, or shorted, preventing indeterminate states.
ESD Protection (Bus Pins) ±15 kV (HBM) ±15 kV (HBM) Robustness against electrostatic discharge on the RS-485 bus lines, important for field-installed equipment.
Supply Voltage 3.0 V to 3.6 V 3.0 V to 3.6 V Operating supply range; both are 3.3 V nominal devices suitable for low-voltage logic systems.
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C Industrial temperature range ensures reliable operation across harsh environments.
Package 8-lead SOIC_N 8-lead SOIC_N Physical footprint and pinout; identical package allows drop-in board compatibility.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM3076EARZ ADM3072EARZ
Part Status Active Active
Type Transceiver Transceiver
Protocol RS422, RS485 RS422, RS485
Number of Drivers/Receivers 1/1 1/1
Duplex Full Half
Receiver Hysteresis 100 mV 100 mV
Data Rate 16Mbps 250kbps
Voltage - Supply 3V ~ 3.6V 3V ~ 3.6V
Operating Temperature -40°C ~ 85°C -40°C ~ 85°C
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the primary differences between the ADM3072EARZ and ADM3076EARZ?

Both are 3.3 V, ±15 kV ESD-protected RS-485/RS-422 transceivers in 8-lead SOIC packages, but they differ in data rate and slew rate. The ADM3072EARZ is a low-speed device specified at 250 kbps with limited slew rate for reduced EMI, while the ADM3076EARZ is a high-speed device specified at 16 Mbps. The ADM3072EARZ also includes a slew-rate-limited driver, whereas the ADM3076EARZ is optimized for higher throughput.

Are the ADM3072EARZ and ADM3076EARZ pin-compatible?

Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows them to share a common PCB footprint, though the data-rate difference must be considered in the system design.

What is the maximum data rate of each device?

The ADM3072EARZ supports a maximum data rate of 250 kbps, while the ADM3076EARZ supports a maximum data rate of 16 Mbps. The lower rate of the ADM3072EARZ is associated with its slew-rate-limited driver, which helps reduce electromagnetic interference.

Do both parts provide the same ESD protection level?

Yes. Both the ADM3072EARZ and ADM3076EARZ are specified with ±15 kV ESD protection on the RS-485/RS-422 bus pins (A and B), using the human body model (HBM), as stated in the Analog Devices datasheet.

Can the ADM3076EARZ be used as a drop-in replacement for the ADM3072EARZ?

Pin compatibility and shared package allow a common footprint, but a direct substitution requires validating the higher 16 Mbps data rate and the non-slew-rate-limited driver against the existing bus topology, cable length, termination, and EMI requirements. The ADM3072EARZ's slew-rate limiting is a functional difference that may affect system EMC performance.

What supply voltage and bus standard do these transceivers support?

Both devices operate from a single 3.3 V supply and are designed for RS-485 and RS-422 communication. They are specified by Analog Devices as 3.3 V, ±15 kV ESD-protected, half-duplex transceivers suitable for industrial bus applications.

How do the receiver and driver enable configurations differ?

Both parts use the same enable scheme: an active-low receiver enable (RE) and an active-high driver enable (DE), allowing independent control of the receiver and driver. This configuration is identical across the ADM3072EARZ and ADM3076EARZ, so control logic does not need to change between the two.